Internal Components

 

Email us direct for Questions at: mrtankless@twlakes.net

 

We show you the inside of our heater & ALL components that make up this well crafted Tankless heater---the craftsmanship is superb & the quality unsurpassed---no other Tankless Hot Water Heater can compare
 

Non Corrosive Resin Heat chamber & elements WILL NOT corrode no matter how hard your incoming water is----This is why we can offer you a LIFETIME WARRANTY

 

We DO NOT use copper or Steel heat chambers OR elements because they are NO GOOD against hard or contaminated water----THEY CORRODE

 

 
The  patented large hybrid water storage heat chamber, water flow sensors & electronic water monitoring sensors, advanced water flow computer,
 
The only HYBRID tankless hot water  heater on the market

LIFETIME WARRANTY on the Non Corrosive Hybrid heat chamber & the Heating Elements

 
                                  
               Non Corrosive   Hybrid Chamber           Water Flow Sensor                            Water Monitoring Sensors
               Gives heater a hotter output           Keeps a constant water temperature          Protects heater from overheating
with less electric use (Advance Resin Design)
 regardless of water flow rate & Hardness                                                                    and monitors power levels for lower cost
       
Uses less electric for its hot water output - This is a 16KW heater that produces 20KW (model EH1620) of Hot water output due to it's Patented over sized water storage chamber with three heating elements - In other words, it consumes 16KW of electric only while you have a hot water faucet turned "ON" while producing 20KW of hot water output at your faucet.
 
When your hot water faucet is turned "OFF" absolutely NO ELECTRIC is being used
 
 

                                                                                      

 Advanced water flow computer that monitors all water flow                              Digital monitor board for control of all sensors &                

through the heater to insure a CONSTANT hot water output                                troubleshooting logic circuits---the most advanced
to all your faucets, tubs and showers  regardless of  changes in                         technology in the Tankless Water Heater Business
your  cold water input levels
                                                              
Click on the "CUSTOMER TESTIMONIAL" Tab at the top of this page  to read our most recent Customer comments

                                                     
 
The digital display & power level board that monitors water                                 The water pressure monitor that assures that
temperature & power levels to the heating elements                                             heater will not be damaged by excessive water
                                                                                                                   pressure---eliminates the need for external pressure relief valves
                                                                                                                           

 

 
 This heater is much less expensive to install due to it's Hybrid design----uses a single cable (#6/2 cable with ground) and  a   single double pole 220volt 70 Amp circuit breaker----that's it !!!!----Yet will produce 20KW hot water output
 
         
 

 

 
 The heaters large digital display panel is very user friendly and  the most advanced of its kind
 
 
The power consumption is controlled by a microprocessor in accordance with the feed temperature and flow rate in order to obtain precisely the set hot-water temperature and to keep it constant despite fluctuations in flow rate. The required value can be entered between 95 degrees and 140 degrees at the push of a button and is indicated by a luminous scale.
 
VERY IMPORTANT NOTE: You Must have a digital temperature gauge on your tankless heater to tell you the setting of the heater----Heaters that DO NOT have this gauge ARE NOT digital & will not allow you to properly be able to control the heater
 
 
 
 Click on the "CUSTOMER TESTIMONIAL" Tab at the top of this page  to read our most recent Customer comments

 
 This heater features both rear and bottom cutouts that allow you to bring your plumbing into the heater either through
your wall into the rear of the heater or exposed piping coming into the heater from the bottom using 1/2" OR 3/4" plumbing
 

 

Click the  "Home Page" Tab at the top of this page to purchase

This page is protected under international copy write laws. Any attempt to copy, use or in any way obtain information from this page without our written consent will be prosecuted to the fullest extent of the law